Portable Pneumatic Hazmat Decon Shower System
The FSI DAT 3060S is a three-line wide (4', 5', 4'), 3 or 4 -station Mass Casualty Decon Shower System which handles three parallel lines of casualties at the same time in three or four sequential stations --- (1) undress, (2) detergent shower #1 - (3) rinse shower #2 OR handle 2 personnel in separate showers simultaneously in each lane, (4) redress. This unit deploys in under two minutes, and processes up to six ambulatory persons at a time or 3 non-ambulatory persons on stretchers simultaneously – or any combination.
Undress and redress stations are dry (plumbing is possible and optional); Four (4) shower stations include 3 showerheads and one hanging coiled ½” hose line with attached multiple function spray nozzle which thoroughly drenches and decontaminates via a fine water mist. The two middle line shower stations include two hanging coiled ½” hose lines w/ attached multiple function spray nozzles. There are a total of 20 water discharge ports as standard. Shutoffs and quick disconnects supplied w/ every group of shower heads and trigger gun. As an option -- by configuring the changing areas on both ends as decon showers one can double the capacity as detailed above. If an optional detergent injector is used then the shower #1 station can be used for detergent cleansing and the shower #2 station may be used for rinse.
Wastewater is contained within integral 13’ W X 12’ L ground floor and 6” berm erected when system is initially inflated (holds 300 gallons of waste water before pump-out is required).
The DAT3060S offers a top center air berm running the entire length of the unit at the roof line and secondary full center length air berms running on either side of the main center berm approx. 18 - 24” off center. FSI offers a total of five 8” - 12” diameter lateral roof support air berms - size of shelter dependent.
System Includes:
- (2) Roll up windows per side
- (2) Skylights
- Roll-up, full zip, dirty entry/clean exit doors
- (8) 19” air duct inlets/outlets w/ tie closures - 2 each on each end/side
- Small electrical duct
- (2) High pressure & (2) low pressure inflation/deflation valves
- Air inflation hose w/ safety cord
- Pressure Relief Valve
- (10) Metal stakes & ground anchor points
- Repair Kit
- Manual
- Shelter sleeve
- (2) Upper air vents
- Hammer
Portable Pneumatic Hazmat Decon Shower System
DAT3060S |
Inside Measurements: |
13’ W X 20’ L X 9’ H |
Outside Measurements: |
14.33' W X 21.33' L X 9' Approx 306ft2 |
Weight: |
335 lbs. |
Carton Size: |
54” L X 43” W X 36” H |
Air pressure internally once inflated: |
4.3 psi |
Total Weight: |
1055 g/m2 |
Thickness: |
0.90 mm |
Cut strip tensile strength: |
Warp = 450 lbs/in Weft = 404 lbs/in |
Elongation: |
Warp = 30% Weft = 47% |
Tongue tear: |
Warp = 87 lbs Weft = 100 lbs |
Adhesion: |
Warp = 9.4 lbs/in Weft = 8.9 lbs/in |
Density: | 30 X 24.5 |
Certifications: |
ANSI 113-200X compliant |
Frame |
Material: |
- Heavy Duty 1100 Dtex polyester coated w/ plastomer on both sides - UV/Chemical resistant - Quadruple overlapped and glued. |
Canopy |
Material: |
- Heavy duty 100% nylon twill (3/5) w/ PU white pigment inner coating - UV/chemical resistant/fire retardant - UV resistant and water repellent w/ a hydrostatic resistance of 250 psi + - - Mildew resistant to meet and exceed US Fed. Test MIL.STD.810E 508 - Fire resistance meets and exceeds CPAI 84 SECTION 5 1995 - US Fed. Test CFR.1610 - Meets NFPA701 Flammability Test method 1 (2004) - NFPA 702 w/ ‘A’ burn scale rating - All seams double stitched and coated both sides. |
Dimensions: |
Approx. 23mm X 57/58 |
Weight: |
Approx. 1.230 gr/m2 |
Inner Canopy |
Material: |
- 100% Nylon 210T Antron Water Resistant Polyurethane Coated 57/58" - Flame Retardant to meet 'NFPA-701 TM-1' - Anti-fungus/Anti-mildew - Opaque |
Color: |
White |
Floor |
Material: | PVC of 0.58mm thickness (1,000 Dtex, 18 X 18 polyester) |
Weight: |
660 gr/mm2 |
Width: |
60 in |
Portable Pneumatic Hazmat Decon Shower System
There are no reviews yet.